DIY

IKEA TARVA Dresser Hack – Angela Marie Manufactured

Just one of the 1st pieces of household furniture I understood I was going to will need for our nursery was a dresser. Following wanting all-around at both of those new and utilized dresser selections, I made a decision to do an IKEA TARVA dresser hack!

The IKEA TARVA dresser is funds pleasant for the sizing, great high-quality for the value, and comes in unfinished wood, so it tends to make painting or staining it tremendous easy for matching your decor! I also like that it’s model new, so I did not have to fret about dealing with any bizarre smells on our child apparel like I might have with acquiring a used dresser!
Just after assembling the dresser for every the IKEA directions, we built a several modifications to the bottom composition of the dresser. It was awkwardly tall and I felt like the dresser legs and foundation built the dresser look…cheap? Not confident if which is the right term, but just not the type I preferred. This was simple to repair with an IKEA dresser hack, by shortening the leg height and including some typical trim. The how-to information are beneath!

Be aware, this publish contains some affiliate inbound links. For a lot more details see my disclosures right here.
Diy IKEA TARVA Dresser Hack:

Materials Necessary:
IKEA TARVA dresser
(1) 4 1/4″ x 8ft baseboard molding (I applied this molding)
1 1/4″ Brad nails
Paint – I applied Kendall Charcoal by Benjamin Moore (eggshell)
Primer
Paint Roller and Paint Brush
Caulk
Lightweight spackle
Painters tape or masking tape
(12) Cabinet knobs

1. Assemble dresser per IKEA directions
Assemble the TARVA dresser for every the IKEA instructions, but you can depart the five dresser legs off. I to begin with assembled my dresser with the legs on to determine the amount of money I needed to slash off for this IKEA dresser hack.

2. Drill holes further on dresser legs
The 5 dresser legs currently have 3/4″ deep pre-drilled holes in the base of them for the plastic ground guard parts. Considering that we are going to be slicing the legs to make them shorter for our IKEA TARVA dresser hack, the holes require to be drilled further very first.
To effortlessly do this, we measured and marked with a pencil 2.5″ from the bottom of every single leg due to the fact that is the quantity that is going to be cut off the base of the legs. Then, mark 3/4″ down from that initially mark.
The next mark is what we need for the depth of our new holes to be. So, lay the 5/16″ drill bit down with the tip lined up with that second mark and then use some painters tape or masking tape to tape off the drill bit wherever you must halt drilling.

Go forward and drill the holes deeper on the 5 dresser legs, halting at the painters tape edge.

3. Slash dresser legs to measurement and install on dresser
Use a miter saw and cut 2.5″ off of the bottom of just about every of the 5 dresser legs. This will change the final dresser height from 36 1/4″ to 33 3/4″ tall.

Following the legs have been minimize, go ahead and install them on the base of the dresser as the unique IKEA directions described.

4. Increase trim to foundation for IKEA TARVA dresser hack
It is time to slice the baseboard molding with a miter saw! Beneath are the reduce measurements I designed for trimming out the dresser, but make guaranteed to double examine the measurements for your own dresser in case there is any slight variation in dimensions.
For the suitable side and still left side of the dresser, the molding really should be lower at a regular 90 degree straight edge on one particular aspect and a 45 diploma bevel slash on the other edge. My measurement was 15 5/8″ from the limited point of the bevel cut to the straight edge for every side. All over again double verify measurements on your precise piece!
Idea: If you don’t know how to make a 45 diploma bevel slash, listed here is a online video I found on Youtube demonstrating how to very easily do this!

Upcoming, lower the entrance molding piece with a 45 degree bevel cut on just about every aspect. My measurement was 59 3/8″ from quick level to brief position.

Connect molding to the dresser with 1 1/4″ brad nails and a brad nailer. Make certain to attach the nails alongside the best edge and into the legs on the corners.
5. Caulk, fill holes, key, and paint IKEA dresser hack
Fill all nail holes in with a lightweight spackle. Then, caulk along the top rated of the baseboard molding and at molding corners to build a seamless look among the molding and dresser.
Upcoming, primary the dresser. This primer is one particular of my favorites for raw wooden. Right after the primer has dried, paint the dresser with two coats of paint and make it possible for to dry. I applied Kendall Charcoal by Benjamin Moore in eggshell and I enjoy this coloration!
Ultimately, include the knobs to the dresser to full your IKEA TARVA dresser hack! Instead of using the knobs bundled with the dresser, I applied these classic, mushroom style cabinet knobs in oil rubbed bronze. They had been the best finishing touch for the typical, rustic type I was attempting to attain with this dresser for our nursery structure.

Now that our nursery dresser makeover is comprehensive, I can not wait around to commence arranging and filling it up with cute baby boy apparel and extras! There is a rationale I started off with this nursery undertaking to start with!
Be sure to abide by together on Instagram and Pinterest for my most current projects, enjoyment updates, and sneak peeks, which includes all of our future nursery jobs!!
Get immediate entry to the library of Absolutely free printables for the residence! Subscribe and get household decor tips, Do-it-yourself tutorials, and entry to the library of Cost-free printables for the house! Results! Now check your electronic mail to affirm your subscription. Accessibility the free printable library at https://angelamariemade.com/absolutely free-printable-library-subscribers/ and enter the password: AMMfreebies Your email affirmation also is made up of this data.

Tags

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Close
Close